Tuesday October 6, 2026 - Antique Tractors & Large Shop Auction

heavy-duty thin-wall axle and spindle nut sockets for trucks, trailers and equipment, in hex and 8-point styles with square drive. Includes a 4-1/8&...

Truck and trailer air brake parts: a stack of Type 30 rubber brake chamber diaphragms (about 6), a chamber clamp ring with bolts, and a brake chamber

One is a convoluted bellows style with two studs (part number appears to be W01-358-8709), and one is a larger rolling-lobe style with four studs. Use

Eight large heavy-duty 6-point sockets with square drive, for truck and trailer axle nuts, hub nuts and heavy equipment. At least one is USA-made. Use

8' Planed Plank & 5' Rough-Sawn Board Black & Decker 7-1/4" combination blade Diablo 8-1/4" framing blade. Two fine-tooth ...

Includes two Sloan Transportation Products bags that appear to hold coiled air brake lines, a coiled trailer electrical cord, a Gates Green Stripe hea

Comes with a set of riveted brake shoes that appear new, a Euclid (Meritor) boxed brake kit and a bagged brake hardware kit (springs, pins, rollers an

Good for barn and building support, leveling and heavy lifting, or rustic décor. Shows age and surface rust. Untested. Sold as is.

Assorted flexible rubber-arm amber marker and clearance lights (at least one marked Model 240), in straight-stalk and L-arm styles. Used on trailers,

Good for lifting, pulling and tensioning. Shows wear and surface rust on the chain. Untested. Not certified for lifting. Sold as is.

Heavy-duty black rubber mud flap with a moulded yellow "DEL" logo, bolted to a galvanized steel angle mounting bracket. Suits dump trucks,...

Traditional oval oak dining table featuring a double pedestal base with curved/turned detailing and extension leaves. Natural golden oak finish and so

Very heavy. Sold as is.

This is a vintage Standard Fasteners Limited No. 701 cotter pin assortment, an Ontario company. It's a metal hinged-lid drawer with 24 compartme...

Not pressure tested. Sold as is. Good for restoration or parts.

The shroud has rust and a bent lower edge. Not pressure tested. Sold as is. Good for restoration or parts.

off an International Harvester / Farmall. Shows rust, bent shroud edges and signs of past solder or weld repairs. Not pressure tested. Sold as is. Goo

The paint is weathered, with traces of green, yellow and red, and there's verdigris on the side tank. No fan shroud. Not pressure tested. Sold a...

The paint is in fair condition and the core looks intact, with light fin damage. Not pressure tested. Sold as is. Good for restoration or parts.

possibly International Harvester / Farmall, with a painted copper/brass core, threaded mounting studs, lower outlet neck, overflow tube and bottom mou

The core fins are heavily corroded and will need recoring. The tanks show verdigris and some traces of red paint. Not pressure tested. Sold as is. For

It has a slotted drive coupling, a bolted cover plate, mounting ears and flange, and threaded ports. Exact use not confirmed. Shows dust and age. Sold

They look like bolt-on or slide-in caster legs for a trailer, a wagon, an implement cart, a hay elevator or a shop dolly. There's surface rust o...

Matched pair of flat steel adjustable bars, each with a row of 9 drilled pin-adjustment holes for length/position adjustment.

Nameplate rated 115 AC volts, 9 amps, 1,000 VA/watts, single phase, 2-wire, 1,800 RPM, 60 cycle, field amps 4, CSA certified. Belt-driven via a multi-

Surface shows a matte black finish with light wear and some surface residue; no visible cracks, splits, or major damage in the photo. A blank tag is z

Galvanized/light-colored finish throughout, with black carbon/soot staining visible inside and around the top opening, consistent with use as a mounte

with three bolt holes on top for attaching to a drawbar or implement frame; below it, a forged jaw/yoke with a pin hole for a hitch pin, cushioned by

Rust staining and an orange/yellow residue mark visible near the top edge; overall surface shows light rust and weathering consistent with the other g

Galvanized gray finish with a rust-stained seam line running the length of the body and light surface rust and grime overall. A flat, angled metal bra

It shows wear consistent with age and use, including surface rust, paint loss, and dirt. The assembly appears complete as pictured, but function of th

Vintage 18-inch pressed steel V-belt pulley in original red paint, with two belt grooves. It has a recessed center with a 3-bolt mounting pattern and

It shows heavy surface rust with traces of old blue-gray paint. Some of the mesh screening near the bottom is torn or missing, and the lower center ed

They are in good overall condition with paint wear, light surface rust, and dirt. One bolt hole has a remnant of old hardware in it. No cracks or chip

The tires are dirty but still hold their shape, with the tread lugs intact. The wheels show surface rust and paint wear. The red part has good paint c

Vintage belt-driven burr mill (grist/feed mill), suitable for grinding corn, grain and feed. Heavy cast iron construction with a pedestal base and bol

Ridgid ratchet die handle: Marked "Ridgid", with traces of the original red paint and a long handle. Ratchet pipe threader die head: Adjus...

Two vintage cast iron screw jacks, suitable for tractor, implement, automotive or display use.

Vintage cast iron right-angle gearbox in red, for PTO-driven equipment. It has a horizontal splined input shaft (appears to be a standard 6-spline PTO

Red double-acting hydraulic cylinder for a tractor or implement. Not tested; condition of the seals is unknown. Sold as is, where is. Please look at a

Heavy-gauge red sheet metal shield or cover panel, formed with rounded bends and pre-drilled mounting holes. It looks like a guard or cover from a vin